| dDischargedDownStreamWaterLevel |
Calculated Discharge derivative with DownStreamWaterLevel. Downstream is relative to the direction of chainage.
The value is calculated by SetWaterLevels.
Unit: [m^2/s]
(Inherited from Structure) |
| dDischargedUpStreamWaterLevel |
Calculated Discharge derivative with UpStreamWaterLevel. Upstream is relative to the direction of chainage.
The value is calculated by SetWaterLevels.
Unit: [m^2/s]
(Inherited from Structure) |
| Discharge |
Calculated Discharge. The value is calculated by SetWaterLevels.
Unit: [m^3/s]
(Inherited from Structure) |
| DownstreamWaterLevel |
Downstream water level.Downstream refers to the direction of chainage. The water level is set by use of
SetWaterLevels
Unit: [m]
(Inherited from Structure) |
| EnableCheckFlowDirectionOscillations |
Flag indicating whether to use special check and damping
for structure discharge oscillating around zero.
(Inherited from Structure) |
| ExtensionData |
Property used by (de)serializer, when it can not find proper target for
a data field. Support of forward compatible data contracts.
(Inherited from Structure) |
| FlowArea |
Flow area through structure. Used by most (but not all) structures.
(Inherited from Structure) |
| FlowFactor |
The discharge (and discharge derivatives) are scaled by the flow factor.
(Inherited from Structure) |
| HQRelation | QH relation for QH and QdeltaH pumps |
| ID |
Structure ID
(Inherited from Structure) |
| IDInUserUnit |
Used to get a consistent description of the structure. The ID comes in user units. Used e.g. when
reporting errors, warnings and hints.
(Inherited from Structure) |
| Implicit |
Flag to control if the structure is implicit or explicit. If the structure is explicit
(Implicit == false) then the derivatives of the dicharge are always zero.
Default value: true
(Inherited from Structure) |
| InvertLevelDownstream |
Invert level down stream
(Overrides StructureInvertLevelDownstream) |
| InvertLevelUpstream |
Invert level up stream
(Overrides StructureInvertLevelUpstream) |
| Length |
Length of the structure.
Unit: [m]
Default value: 0m
(Inherited from Structure) |
| Location |
Location property.
(Inherited from Structure) |
| Offset | Offset on QH relation, subtracted from the water level before looking up in the HQRelation |
| RunTimeDiagnostics |
The getter is used to get a list of errors.
(Inherited from Structure) |
| SideStructureBank |
Bank side that side-structure is located on
If side structure contains reservoir, and has the Coordinate set, this is not used (and should be set to Undefined). (Inherited from Structure) |
| SideStructureReservoir |
Reservoir at end of side structure. Null if not side structure, or no reservoir is defined
(Inherited from Structure) |
| SmoothingFactor |
Exponential smoothing factor for structure discharge.
The smoothing factor is the weight of the previous discharge on the new discharge:
q = (1 - SmoothingFactor) * qStructure + SmoothingFactor * qPrevious
(Inherited from Structure) |
| StructureType |
Type of structure
(Inherited from Structure) |
| TopoID |
String used to identified cross sections
(Inherited from Structure) |
| Type |
Structure type, unique for each structure.
(Overrides StructureType) |
| UpstreamWaterLevel |
Upstream water level. Upstream refers to the direction of chainage. The water level is set by use of
SetWaterLevels
Unit: [m]
(Inherited from Structure) |
| WaterLevelDifferenceMinimal |
Water level difference below which it is assumed
that structure has no flow.
(Inherited from Structure) |