ICulvert Interface |
Models the flow through typically longer pipe between limiting cross sections (up- and down- stream).
The pipe my have any cross section geometry and may be either closed or open.
The culvert such that critical flow conditions are calculated prior to calculation of the actual flow. The
critical flow conditions are typically by activating the CalcCriticalConditions method from a
user interface The result of this procedure is stored as part of the culvert specification.
Namespace: DHI.Mike1D.StructureModule
Assembly: DHI.Mike1D.StructureModule (in DHI.Mike1D.StructureModule.dll) Version: 19.0.0.0 (11.1.1.1111)
SyntaxThe ICulvert type exposes the following members.
Properties| Name | Description | |
|---|---|---|
 | dDischargedDownStreamWaterLevel |
Calculated Discharge derivative with UpStreamWaterLevel. Upstream is relative to the direction of chainage.
Unit: [m^2/s]
(Inherited from IStructure.) |
| dDischargedUpStreamWaterLevel |
Calculated Discharge derivative with DownStreamWaterLevel. Downstream is relative to the direction of chainage.
Unit: [m^2/s]
(Inherited from IStructure.) |
| Delhs |
Level from where the variation is forced to be linear.
(Inherited from ILinearZeroVariation.) |
| Discharge |
Calculated Discharge
Unit: [m^3/s]
(Inherited from IStructure.) |
| DownstreamInvertLevel |
The invert level downstream.
Unit: [m]
|
| DownstreamWaterLevel |
Downstream water level.Downstream refers to the direction of chainge. The water level is set by use of
SetWaterLevels
Unit: [m]
(Inherited from IStructure.) |
| FlowFactor |
The discharge (and discharge derivatives) are scaled by the flow factor.
(Inherited from IStructure.) |
| Geometry |
Class describing the geometry of the culvert section
|
| HeadLossBendsNegativeFlow |
Bends head loss factor for negative flow.
Unit: []
|
| HeadLossBendsPositiveFlow |
Bends head loss factor for positive flow.
Unit: []
|
| HeadLossFreeOverflowNegativeFlow |
Free overflow factor for negative flow.
(Inherited from IHeadLossStructure.) |
| HeadLossFreeOverflowPositiveFlow |
Free overflow factor for positive flow.
(Inherited from IHeadLossStructure.) |
| HeadLossInflowNegativeFlow |
Inflow head loss factor for negative flow.
(Inherited from IHeadLossStructure.) |
| HeadLossInflowPositiveFlow |
Inflow head loss factor for positive flow.
(Inherited from IHeadLossStructure.) |
| HeadLossOutflowNegativeFlow |
Outflow head loss factor for negative flow.
(Inherited from IHeadLossStructure.) |
| HeadLossOutflowPositiveFlow |
Outflow head loss factor for positive flow.
(Inherited from IHeadLossStructure.) |
| HorizontalOffSetFromMarker2 |
Horizontal offset of the structures compared to its limiting cross sections.
(Inherited from IPlotableStructure.) |
| HydraulicParameters |
Hydraulic parameters for the given geometry.
|
| ID |
Name of the structure.
(Inherited from IStructure.) |
| IDInUserUnit | Obsolete.
Used to get a consistent description of the structure. The ID comes in user units. Used e.g. when
reporting errors, warnings and hints.
(Inherited from IStructure.) |
| Implicit |
Flag to control if the structure is implicit or explicit. If the structure is explicit
(Implicit == false) then the derivatives of the discharge are always zero.
Default value: true
(Inherited from IStructure.) |
| InvertLevelDownstream |
Invert level down stream
The invert level is the level where water starts
flowing in to the structure from the downstream side.
It does not necessarily flow through the structure.
(Inherited from IStructure.) |
| InvertLevelUpstream |
Invert level up stream.
The invert level is the level where water starts
flowing in to the structure from the upstream side.
It does not necessarily flow through the structure.
(Inherited from IStructure.) |
| Length |
Length of the culvert.
Unit: [m]
Default: 0
|
| Location |
Location of structure.
(Inherited from IStructure.) |
| Mannings_n |
Mannings n.
Unit: [s/m^(1/3)]
|
| Multiplicator |
Multiplicator or "number of culverts". Used for modelling more culverts in one go.
Unit: []
Default: 1
|
| OrificeFlowCoefficientsNegativeFlow |
Orifice flow coefficients for negative flow
|
| OrificeFlowCoefficientsPositiveFlow |
Orifice flow coefficients for positive flow
|
| PartOfCompositeFlow |
Part of the flow in a parallel strucutre that passes through this structure.
(Inherited from ISolvesEnergyEquation.) |
| QhFlowtypeRelationsNegativeFlow |
Q/h relations for negative flow
|
| QhFlowtypeRelationsPositiveFlow |
Q/h relations for positive flow
|
| RunTimeDiagnostics |
The getter is used to get a list of errors. OBSOLETE
(Inherited from IStructure.) |
| SideStructureBank |
Bank side that side-structure is located on
(Inherited from IStructure.)If side structure contains reservoir, and has the Coordinate set, this is not used (and should be set to Undefined). |
| SideStructureReservoir |
Reservoir at end of side structure. Null if not side structure, or no reservoir is defined
(Inherited from IStructure.) |
| StructureIterationCentering |
Used when making relaxation when iterating to find the subcritical solution for structures solved using the energy equation.
When it equals 1 no relaxation is made.
(Inherited from IHeadLossStructure.) |
| StructureType |
Type of structure
(Inherited from IStructure.) |
| TopoID |
TopoID used when structure is searching for neighboring cross sections in the reach.
(Inherited from IStructure.) |
| Type |
Structure type, unique for each type of structure.
(Inherited from IStructure.) |
| UpstreamInvertLevel |
The invert level upstream.
Unit: [m]
Default: 0
|
| UpstreamWaterLevel |
Upstream water level. Upstream refers to the direction of chainage. The water level is set by use of
SetWaterLevels
Unit: [m]
(Inherited from IStructure.) |
| Valve |
Type of valve giving the direction of flow that is possible.
(Inherited from IValvedStructure.) |
Methods| Name | Description | |
|---|---|---|
 | Accepts |
List of data types that is accepted, i.e., that you can get a ValueSetter for.
(Inherited from IQuantityProxy.) |
| CalculateFlowConditions |
Call this method to produce Qh relations from culvert data.
|
| Description |
Description of the structure.
(Inherited from IStructure.) |
| Initialize |
Set up structure and set runtime diagnostics object
(Inherited from IStructure.) |
| Offers |
List of data types that is offered, i.e., that you can get a ValueGetter for.
(Inherited from IQuantityProxy.) |
| Prepare |
Set up structure and set runtime diagnostics object
(Inherited from IStructure.) |
| SetWaterLevels(Double, Double) |
Sets up- and down- stream water level and forces the calculation of the discharge and its derivatives.
(Inherited from IStructure.) |
| SetWaterLevels(Double, Double, Double, Double) |
Sets up- and down-stream water level and forces the calculation of the discharge and its derivatives.
(Inherited from ISolvesEnergyEquation.) |
| UpdatedWaterLevels |
After a time step (or iteration) has finished, update the discharge to the actual value, based
on the final water levels and the discharge derivatives.
(Inherited from IStructure.) |
| Validate |
Writes errors, warnings and hints into their respective member classes. The member objects are initially cleared.
(Inherited from IStructure.) |
| ValueGetter |
Get value setter for the specified data quantity
(Inherited from IDoubleProxy.) |
| ValueSetter |
Get value setter for the specified data type
(Inherited from IDoubleProxy.) |
Extension Methods| Name | Description | |
|---|---|---|
 | Getter | From the proxy, return an FuncTResult for the specified quantity. It returns the first quantity of that type that is offered, and null if the quantity is not offered. |
| Getters |
Returns a set of FuncTResult for the quantity.
We can return several quantities with the same id (usually they will differ in their description).
If the quantity is not offerent, an empty list is returned.
(Defined by ProxyExtensions.) |
| GettersFraction |
Returns a set of FuncT, TResult for the quantity.
We can return several quantities with the same id (usually they will differ in their description).
If the quantity is not offerent, an empty list is returned.
(Defined by ProxyExtensions.) |
| GetterUnboxed | From the proxy, return an FuncTResult for the specified quantity. It returns the first quantity of that type that is offered, and null if the quantity is not offered. |
| Initialize(CrossSectionData, Boolean, IDiagnostics) | Overloaded.
Helper function for some unit tests. Do not use.
(Defined by StructureExtensions.) |
| Initialize(BoundaryData, CrossSectionData, Boolean, IDiagnostics) | Overloaded.
Helper function for some unit tests. Do not use.
(Defined by StructureExtensions.) |
| IsSideStructure |
Returns true if the structure is a side structure
(Defined by StructureExtensions.) |
| Setter | From the proxy, return an IDoubleGetSet for the specified quantity. It returns the first quantity of that type that is accepted, and null if the quantity is not accepted. |
See Also