public interface IStormwaterInlet : IStructure,
IDoubleProxy, IQuantityProxy| Blockage | Blockage is the ratio of flow in the inlet that is blocked by debris. |
| dDischargedDownStreamWaterLevel |
Calculated Discharge derivative with UpStreamWaterLevel. Upstream is relative to the direction of chainage.
Unit: [m^2/s]
(Inherited from IStructure) |
| dDischargedUpStreamWaterLevel |
Calculated Discharge derivative with DownStreamWaterLevel. Downstream is relative to the direction of chainage.
Unit: [m^2/s]
(Inherited from IStructure) |
| DepthQRelation | Table of Q values in the inlet as a function of depth in the source node. |
| Discharge |
Calculated Discharge
Unit: [m^3/s]
(Inherited from IStructure) |
| DownstreamWaterLevel |
Downstream water level.Downstream refers to the direction of chainge. The water level is set by use of
SetWaterLevels
Unit: [m]
(Inherited from IStructure) |
| FlowFactor |
The discharge (and discharge derivatives) are scaled by the flow factor.
(Inherited from IStructure) |
| Freeboard | Freeboard is the distance between the invert level of the inlet to the maximum downstream water level. If the downstream water level exceeds the inlet level minus the freeboard, then the inlet functions as an orifice instead of a storm water inlet. |
| Height | Height of the inlet when it functions as an orifice. |
| ID |
Name of the structure.
(Inherited from IStructure) |
| IDInUserUnit |
Used to get a consistent description of the structure. The ID comes in user units. Used e.g. when
reporting errors, warnings and hints.
(Inherited from IStructure) |
| Implicit |
Flag to control if the structure is implicit or explicit. If the structure is explicit
(Implicit == false) then the derivatives of the discharge are always zero.
Default value: true
(Inherited from IStructure) |
| InvertLevel | Invert level of the inlet. |
| InvertLevelDownstream |
Invert level down stream
The invert level is the level where water starts
flowing in to the structure from the downstream side.
It does not necessarily flow through the structure.
(Inherited from IStructure) |
| InvertLevelUpstream |
Invert level up stream.
The invert level is the level where water starts
flowing in to the structure from the upstream side.
It does not necessarily flow through the structure.
(Inherited from IStructure) |
| Length |
Length of the structure.
Unit: [m]
(Inherited from IStructure) |
| Location |
Location of structure.
(Inherited from IStructure) |
| NumberOfInlets | Number of inlets. The flow through the Stormwater Inlet structure is the flow through a single inlet multiplied by the number of inlets. |
| OnGradeInlet | When true then the stormwater inlet is of the OnGrade type where inlet discharge is a function of the upstream discharge and the slope of the upstream reaches. If false, then the inlet discharge is a function of the upstream water level. |
| QqRelations | List of Q values in the inlet as a function of q in the source pipe. |
| RunTimeDiagnostics |
The getter is used to get a list of errors. OBSOLETE
(Inherited from IStructure) |
| SideStructureBank |
Bank side that side-structure is located on
If side structure contains reservoir, and has the Coordinate set, this is not used (and should be set to Undefined). (Inherited from IStructure) |
| SideStructureReservoir |
Reservoir at end of side structure. Null if not side structure, or no reservoir is defined
(Inherited from IStructure) |
| Slopes | List of slopes in the source pipe. These slopes are matching the values in the QqRelations. |
| StructureType |
Type of structure
(Inherited from IStructure) |
| TopoID |
TopoID used when structure is searching for neighboring cross sections in the reach.
(Inherited from IStructure) |
| Type |
Structure type, unique for each type of structure.
(Inherited from IStructure) |
| UpstreamWaterLevel |
Upstream water level. Upstream refers to the direction of chainage. The water level is set by use of
SetWaterLevels
Unit: [m]
(Inherited from IStructure) |
| UserDefinedSlope |
If UserDefinedSlope is set, then this value is used for the slope of the source
pipe instead of the actual slope from the network geometry.
Set to MinValue to disable the use of it. |
| Width | Width of the inlet when it functions as an orifice |
| Accepts |
List of data types that is accepted, i.e., that you can get a ValueSetter for.
(Inherited from IQuantityProxy) |
| AddQQRelation | Add a QQ relation for the specified slope. Must be added in order of increasing slope. |
| ClearQQRelations | Clear all QQ Relations |
| Description |
Description of the structure.
(Inherited from IStructure) |
| Initialize |
Set up structure and set runtime diagnostics object
(Inherited from IStructure) |
| Offers |
List of data types that is offered, i.e., that you can get a ValueGetter for.
(Inherited from IQuantityProxy) |
| Prepare |
Set up structure and set runtime diagnostics object
(Inherited from IStructure) |
| SetWaterLevels |
Sets up- and down- stream water level and forces the calculation of the discharge and its derivatives.
(Inherited from IStructure) |
| UpdatedWaterLevels |
After a time step (or iteration) has finished, update the discharge to the actual value, based
on the final water levels and the discharge derivatives.
(Inherited from IStructure) |
| Validate |
Writes errors, warnings and hints into their respective member classes. The member objects are initially cleared.
(Inherited from IStructure) |
| ValueGetter |
Get value setter for the specified data quantity
(Inherited from IDoubleProxy) |
| ValueSetter |
Get value setter for the specified data type
(Inherited from IDoubleProxy) |
| Getter | From the proxy, return an FuncTResult for the specified quantity. It returns the first quantity of that type that is offered, and null if the quantity is not offered. (Defined by ProxyExtensions) |
| Getters |
Returns a set of FuncTResult for the quantity.
We can return several quantities with the same id (usually they will differ in their description).
If the quantity is not offerent, an empty list is returned.
(Defined by ProxyExtensions) |
| GettersFraction |
Returns a set of FuncT, TResult for the quantity.
We can return several quantities with the same id (usually they will differ in their description).
If the quantity is not offerent, an empty list is returned.
(Defined by ProxyExtensions) |
| GetterUnboxed | From the proxy, return an FuncTResult for the specified quantity. It returns the first quantity of that type that is offered, and null if the quantity is not offered. (Defined by ProxyExtensions) |
| Initialize |
Helper function for some unit tests. Do not use.
(Defined by StructureExtensions) |
| Initialize |
Helper function for some unit tests. Do not use.
(Defined by StructureExtensions) |
| IsSideStructure |
Returns true if the structure is a side structure
(Defined by StructureExtensions) |
| Setter | From the proxy, return an IDoubleGetSet for the specified quantity. It returns the first quantity of that type that is accepted, and null if the quantity is not accepted. (Defined by ProxyExtensions) |